Available 24/7 St. Louis 314-876-8048 Kansas City 816-683-1099
George & SonsChimney Services

Installations & upgrades

Chimney Installation

A new chimney isn't bought off a shelf — it's planned around the appliance it serves, the path it takes through the house, and the clearances that keep it safe. Here's how that planning works.

Two George & Sons technicians servicing a brick chimney on a roof

Installing a chimney is one of those jobs that looks straightforward from the outside — put a stack up, run it through the roof — and turns out to be genuine engineering once you look closely. A chimney is a venting system, and a venting system has to be planned around the appliance it serves, routed sensibly through the house, supported properly, terminated at the right height, and kept at safe clearances from everything combustible along the way. Get those right and the chimney drafts well and vents safely for decades. Skip the planning and you get a chimney that draws poorly, or worse. Chimney installation, done right, is mostly about the thinking that happens before the first component goes up.

It starts with the appliance

The single most important principle: a chimney is planned around what it vents.

The appliance and fuel — a wood stove, a fireplace, a gas appliance — determine what kind of chimney is needed, how it must be sized, and what venting requirements it has to meet. You can't properly plan a chimney without knowing what it serves.

This is why appliance selection and chimney installation are inseparable. The appliance's manufacturer specifies the venting requirements, and the chimney is sized and configured to meet them. A flue that's the wrong size — too small to vent the appliance, or so large that gases cool and draft poorly — undermines the whole system. So "I need a chimney" always begins with "for what?"

Masonry versus factory-built

One of the first decisions is the type of chimney:

  • Masonry chimney — site-built from brick, block and flue tile, a permanent masonry structure. Durable and traditional, but a bigger, costlier build.
  • Factory-built chimney — a manufactured metal system (insulated double- or triple-wall pipe, often called Class A), assembled from listed components and frequently run inside a framed chase. Faster to install and often more economical.

They're genuinely different installations with different costs, requirements and timelines, and which is appropriate depends on the appliance, your home's structure, and your goals and budget. We help you weigh them rather than defaulting to one.

Route, support and termination

Three planning decisions shape how well the finished chimney works:

  • Route. The path through the house affects draft, support, and how the chimney interacts with the structure. A straight, interior, well-insulated route generally drafts better and stays warmer than a long, offset, or exterior one. We look for a route that vents well and works with your construction.
  • Support. A chimney has to be properly supported along its run and where it passes through floors, ceilings and the roof — with correct brackets, firestops and structural attention.
  • Termination. The chimney terminates above the roof at a height determined by requirements that account for roof slope and nearby structures, topped with an appropriate crown or cap and a suitable termination.

None of these is an afterthought; together they're most of what makes a chimney draft and vent as it should.

Clearances: the safety fundamental

If there's one thing a chimney installation cannot get wrong, it's clearances:

Clearances are the required minimum distances between the chimney and any combustible materials — framing, insulation, finishes — as it passes through the structure. They exist because a chimney gets hot, and combustible material too close to it is a fire risk. A proper installation maintains these listed clearances throughout the route, using firestops and correct components wherever the chimney penetrates floors, ceilings, walls and the roof. This isn't a detail to approximate; it's foundational to a safe chimney, and it's a core part of what we're planning and verifying.

Matching the chimney to the appliance

It bears repeating as its own point: not any appliance connects to any chimney. The chimney has to be suitable in type, size and material for the specific appliance and fuel — a chimney built for one can be genuinely wrong for another. This is why we match the chimney to the appliance rather than installing a generic stack. For relining an existing flue to suit a new or different appliance, that's liner installation; for a fresh chimney, it's matching the whole system from the start. Either way, the appliance governs.

Permitting, honestly

Chimney installations typically involve local permitting and must meet applicable requirements, and the specifics vary by jurisdiction. We work within the requirements that apply, and verifying the exact local permitting and inspection process is done with your local authority as part of planning. We won't claim a blanket "no permit needed" or overstate what's required — the honest answer is that it depends on your location, and it's confirmed with the actual jurisdiction. Getting the permitting right is part of a legitimate installation.

What affects the scope

Chimney installation scope depends on the appliance and fuel, the chimney type (masonry versus factory-built), the route and its complexity, the structure, the termination requirements, and local permitting. A factory-built chimney on a straightforward interior route is one kind of project; a masonry build or a complex route is a larger one. We plan it around your specific situation.

Preparing for the consultation

  • Tell us what appliance the chimney will serve (or that you're also choosing the appliance).
  • Describe the space and where you'd want the appliance and chimney.
  • Mention any goals — efficiency, appearance, budget — and your timeline.
  • Note anything about your home's construction that might affect routing.

A chimney installation is an exercise in matching a venting system to an appliance and a house — the right type, sized correctly, routed well, terminated properly, and safely clear of everything combustible. Plan all of that with care and the chimney simply works, safely, for a very long time. That planning is the heart of the job, and it's where we start.

Questions about chimney installation

What goes into planning a chimney installation?

More than most people expect. It starts with the appliance the chimney will serve — a wood stove, a fireplace, a gas appliance — because the appliance and fuel determine what kind of chimney is needed and how it must be sized. From there: the route the chimney takes through the house, how it's supported, where it terminates above the roof, and the required clearances to combustible materials along the whole path. A chimney is an engineered venting system, planned around its specific job, not a generic stack.

What's the difference between a masonry and a factory-built chimney?

A masonry chimney is site-built from brick, block and flue tile — a permanent masonry structure. A factory-built chimney is a manufactured metal system (insulated double- or triple-wall pipe, often called Class A) assembled from listed components, frequently run inside a framed chase. They're genuinely different installations with different costs, requirements and timelines. Which is appropriate depends on the appliance, the structure, your goals and budget — it's one of the first decisions in planning.

How is the chimney sized?

To the appliance it serves. The flue has to be the right size for the appliance's output and venting requirements — too small restricts it, too large lets gases cool and draft poorly. The manufacturer of the appliance specifies venting requirements, and the chimney is sized and configured to meet them. This is why appliance selection and chimney installation go hand in hand: you can't properly size a chimney without knowing what it's venting.

What are 'clearances to combustibles' and why do they matter?

Clearances are the required minimum distances between the chimney and any combustible materials — framing, insulation, finishes — as the chimney passes through floors, ceilings, walls and the roof. They exist because a chimney gets hot, and combustible material too close to it is a fire risk. Proper installation maintains these listed clearances throughout the chimney's route, using firestops and correct components where it passes through the structure. Getting clearances right is fundamental to a safe installation, not an optional detail.

Does the chimney route through my house matter?

A lot. The path the chimney takes affects how well it drafts, how it's supported, how many offsets it needs, and how it interacts with the structure. A straight, interior, well-insulated route generally drafts better and stays warmer than a long, offset, or exterior one. Part of planning is finding a route that vents well and works with your home's construction — it's not just 'up through the nearest spot.'

Where does the chimney have to terminate?

Above the roof, at a height determined by requirements that account for the roof's slope and nearby structures — often described by rules about how far the chimney must extend above the roof penetration and above anything within a certain horizontal distance. Proper termination height matters for draft and safety, and it's topped with an appropriate crown or cap and a termination suited to the system. We plan the termination as part of the whole, not as an afterthought.

Do I need a permit for a chimney installation?

Installations typically involve local permitting and must meet applicable requirements, and the specifics vary by jurisdiction. We work within the requirements that apply, and verifying the exact local permitting and inspection process is done with your local authority. We won't claim a blanket 'no permit needed' or overstate what's required — the honest answer is that it depends on your location, and it's confirmed with the actual jurisdiction as part of planning a proper installation.

Can any appliance connect to any chimney?

No. The chimney has to be suitable — in type, size and material — for the specific appliance and fuel. A chimney built for one appliance can be wrong for another. This is why we don't just 'add a chimney'; we match the chimney to the appliance it will serve, which is the core of doing an installation correctly. Trying to connect an appliance to an unsuitable chimney is a performance and safety problem, not a shortcut.

Works with

Related services

Chimney and fireplace problems rarely sit in isolation. These related services often come up alongside this one.

A chimney top opened for relining with clay flue tile visible Installations

Chimney Liner Installation & Relining

Discuss sizing and material compatibility for the actual appliance/fuel, insulation where required, existing-flue condition and...

View service →
A fireplace insert set into a stone-veneer surround with a timber mantel Installations

Fireplace Installation

Provide a planning guide by fuel/system, structural/site constraints, venting and clearances; link to the specific installation...

View service →
Glowing coals inside a wood-burning firebox Installations

Wood Stove Installation

Address placement, floor protection, clearances, connector/chimney route and sizing; keep appliance selection separate from...

View service →
A metal flue cap and storm collar on a factory-built chimney Related

Gas Appliance Chimney & Venting Services

Focus on the chimney/vent serving an appliance, compatibility and observed venting concerns; do not imply general furnace, boiler...

View service →
Video Installations

Chimney Cap Installation

Explain single-/multi-flue or custom fit, attachment and component compatibility; distinguish a new cap from repairing an existing...

View service →
A black chase cover and cap installed on a sided chimney chase Chimney

Metal Chimney & Vent Pipe Repair

Discuss corrosion, connection integrity, supports and system listing; do not mix unrelated pipe brands/components or treat sealant...

View service →

All 76 services →

Serving Missouri, Illinois & Kansas

Ready when you are — available 24/7

Reach the office nearest you, or send your details and we’ll plan the next step.

St. Louis · 314-876-8048 Kansas City · 816-683-1099 Request service

Request Service Call us