The chimney camera has changed how flues are inspected, and mostly for the better. Before affordable, maneuverable cameras, the inside of a flue above the firebox was largely a matter of inference. Now we can send a camera up and actually look. That's a genuine advance — but it's also become one of the most oversold tools in the trade, with "camera inspection" sometimes presented as if a video clip were the whole of an inspection. It isn't, and understanding both the camera's real value and its real limits is the point of this page.
What a video scan documents
Used within an inspection, a camera is excellent at one specific job: showing the interior of the flue along its line of sight. That includes:
- The liner's condition — whether clay tiles are intact, cracked, spalled or displaced, or whether a metal liner shows damage.
- Gaps and joints between tile sections where gases could escape.
- Deposits — the amount, location and type of creosote or soot coating the flue.
- Obstructions — nests, debris or fallen material blocking the passage.
For a homeowner, the real power is that we can show you the problem. Pointing at an actual crack on a screen is far more persuasive — and more honest — than describing it from the ground. When we recommend work, the camera is often how you see exactly why.
The limits worth understanding
Every tool has a working envelope, and the camera's is defined by line of sight. It sees what it can point at along a reasonably clear path. What it struggles with:
- Offsets and bends. Many flues aren't perfectly straight, and the camera's view is interrupted where the flue jogs.
- Heavy deposits and obstructions. The camera can't see through a thick creosote layer or past a blockage — which is one reason a flue is cleaned before a thorough scan, so the surface is actually visible.
- Behind the liner. The camera documents the inside surface of the flue. It cannot see into the chimney's structure behind that surface — the masonry, the framing, the concealed areas that a Level 3 inspection exists to reach.
A good inspector is as aware of what the camera isn't showing as what it is. The limitations aren't a flaw; they're just the reason the camera is one input rather than the whole evaluation.
Why a clip isn't an inspection
This is the distinction we most want homeowners to hold onto. A camera scan documents the flue interior. A full inspection evaluates the entire system — the crown, cap and termination at the top; the exterior masonry and the flashing where the chimney meets the roof; the smoke chamber, damper and firebox; the connected appliance and its venting; and the structural interaction a camera can't see. The camera informs part of that; professional judgment ties it all together.
A video scan offered on its own — especially as a free lead-in to selling work — is not the same as an impartial, complete inspection. We use the camera fully, but as an honest tool within a real inspection, not as a substitute for one.
Where the camera fits best
There are situations where a video scan is genuinely close to indispensable, and they're mostly the situations that call for a Level 2 inspection in the first place:
- After a chimney fire, to find heat-cracked tiles invisible from the firebox — see post-fire inspection.
- During a home sale, to document the flue's condition for both parties.
- Diagnosing a suspected flue or liner problem, where the scan confirms the extent before deciding between tile repair, liner repair or relining.
- Locating a blockage precisely before clearing it, so it's removed without damaging the flue.
Reading what the camera shows
Pointing a camera up a flue is the easy part; knowing what you're looking at is where experience comes in. The inside of a flue is a harsh visual environment — soot darkens surfaces, deposits cast shadows, moisture reflects the light, and the camera's own lighting can make a harmless mark look alarming or a real crack look like nothing. A hairline crack in a clay tile, a separated joint, a spalled section, and a simple soot streak can all look surprisingly similar to an untrained eye on a small screen.
Interpreting the footage correctly means distinguishing genuine defects from visual artifacts, understanding how flue tiles are built and where they typically fail, and recognizing when what the camera can't quite resolve needs a different vantage point or a cleaning first. It's the difference between documenting a flue and understanding one.
This is another reason a camera scan belongs inside a real inspection rather than standing alone. The value isn't just the footage — it's an experienced read of what the footage means, tied to everything else the inspection establishes. When we show you something on screen, we'll explain what it is, why it matters, and how confident we are about it, rather than letting an ambiguous image speak for itself.
What affects the scope
A camera scan's usefulness depends on the flue being accessible and reasonably clear — heavy deposits usually mean a cleaning first — and on the flue's layout, since offsets limit what any camera can see. We'll tell you honestly what the scan could and couldn't capture on your specific chimney rather than implying it saw everything.
Preparing for the visit
- Let the chimney go cold before we arrive.
- If the flue is heavily sooted, expect that a cleaning may be needed first for a meaningful scan.
- Mention what prompted the scan — a sale, a fire, a suspected crack, a blockage — so we focus on the right questions.
A chimney camera is a genuinely valuable tool, and we use it to full effect. We just use it the honest way: as one clear window into the flue, within a complete inspection that looks at the whole system.