Available 24/7 St. Louis 314-876-8048 Kansas City 816-683-1099
George & SonsChimney Services

Fireplace & appliance repairs

Gas Fireplace Pilot & Ignition Repair

Most gas fireplaces that won't start fail right here — at the pilot or the ignition. The fix depends on which ignition system you have, and it never means bypassing a safety control.

A gas fireplace burning behind a glass front

When a gas fireplace won't start, the trouble is most often right at the beginning of the sequence — the pilot and the ignition system that's supposed to bring the fire to life. It's also where the safety architecture of a gas appliance lives, in the flame-sensing components that make sure gas only flows when there's a flame to burn it. That combination — common failure point, critical safety role — is why pilot and ignition repair deserves care and why it's never a place for shortcuts. The fix starts with knowing which ignition system you have, and it always respects the safety controls rather than defeating them.

Two ignition systems, two personalities

The first thing to establish is which type of ignition your fireplace uses, because they fail and are repaired differently:

  • Standing pilot keeps a small pilot flame burning continuously, ready to light the main burner on demand. It's simple and reliable, uses a little gas constantly, and relies on a thermocouple and/or thermopile to sense the pilot flame.
  • Electronic ignition (intermittent pilot or direct spark) lights only when you call for a fire, saving gas, but adds electronics — an ignition module, igniter, and sensors.

A standing-pilot fault is often a thermocouple or thermopile; an electronic-ignition fault might be the module or igniter. Identifying the system is genuinely step one, because it points the whole diagnosis.

Reading the symptom

The specific way the ignition misbehaves tells us a lot:

  • Pilot won't spark at all → often the igniter or, on electronic systems, the module.
  • Pilot sparks but won't catch → a dirty or blocked pilot orifice, gas supply, or air in the line.
  • Pilot lights but goes out when you release the knob → the classic thermocouple symptom on a standing-pilot system.
  • Lights and runs briefly, then dies → often a weak or failing thermopile, or a safety sensor.

Each behavior points somewhere different, which is why we ask you to describe exactly what happens — and watch it ourselves — rather than assuming. The symptom is the first clue in the diagnosis.

The flame sensors: thermocouple and thermopile

These small components do an outsized safety job, and they're among the most common ignition failures:

A thermocouple generates a small voltage from the pilot's heat that keeps the pilot gas valve open — if the pilot goes out, the voltage drops and the valve closes, shutting off gas. A thermopile (a bundle of thermocouples) generates more voltage, enough to operate the main valve and controls on many millivolt systems.

When one of these is failing, dirty, or misaligned so it isn't sensing the flame properly, the result is a pilot that won't stay lit or a fireplace that won't start or stay running. Testing them tells us which has failed, and replacing the faulty one with a compatible part is a well-defined repair.

The rule we never break: no bypassing safety controls

This is the most important point on the page, and we state it without hedging:

The flame-sensing safety controls exist to shut off gas when there's no flame to burn it — preventing raw, unburned gas from flowing into your home. Bypassing, jumping, or defeating them to force the fireplace to run removes that protection and is genuinely dangerous. We repair or replace the faulty safety component with the correct part so the system works as designed. We never disable a safety control to make a symptom disappear — and if you ever find instructions online to do so, please don't. The safety system isn't the problem; a failed component in it is, and that's what gets fixed.

Why compatible parts matter

Ignition components are matched to the specific appliance, its valve, and its control system. The wrong thermocouple, thermopile, igniter or module may not generate the right voltage, fit correctly, or integrate with the safety system — leaving the fireplace unreliable or unsafe. We use parts compatible with your make and model rather than a generic approximation, so the ignition and safety system functions exactly as the manufacturer intended. With safety-critical components, "close enough" isn't a standard we apply.

Where ignition fits in gas fireplace repair

Ignition repair is the focused specialty within the broader gas fireplace repair category — specifically the starting and flame-sensing system. Most "won't light" calls land here, which is why it has its own page. But if the diagnosis points to the burner, the valve, the venting, or elsewhere, we address that instead. We follow the actual fault rather than forcing every no-start into an ignition fix.

What affects the scope

Ignition repair scope depends on the ignition system type, which component has failed, the make and model and the availability of compatible parts, and whether the fault is isolated or part of a larger issue. A thermocouple replacement is a defined job; an electronic ignition module or a multi-component fault is more involved. Diagnosis comes first.

Preparing for the visit

  • Describe exactly what happens when you try to light it — sparks, catches, dies, nothing.
  • Note whether you have a standing pilot (always-on flame) or electronic ignition.
  • On electronic/remote systems, try fresh batteries first; it's a legitimate owner step.
  • Never troubleshoot a gas smell — leave and call your utility. Otherwise let the unit cool and clear access.

Pilot and ignition problems are the most common reason a gas fireplace goes dark, and they're very fixable — with the right diagnosis, the correct compatible part, and an absolute respect for the safety controls that make a gas appliance safe to use. That last part is non-negotiable, and it's exactly how we work.

Questions about gas fireplace pilot & ignition repair

What's the difference between a standing pilot and electronic ignition?

A standing-pilot system keeps a small pilot flame burning continuously, ready to light the main burner on demand — simple and reliable, but it uses a little gas constantly and relies on a thermocouple/thermopile to sense the flame. An electronic ignition (intermittent pilot or direct spark) lights the pilot or burner only when you call for a fire, saving gas, but it has more electronics — an ignition module, igniter, and sensors. They fail differently and are repaired differently, so identifying which you have is step one.

My pilot won't light. What's the likely cause?

Common causes include a dirty or blocked pilot orifice, a failed igniter (the spark component), a gas supply issue, air in the line, or on electronic systems a fault in the ignition module. A pilot that sparks but won't catch, versus one that won't spark at all, versus one that lights but goes out, each point in different directions — so the specific behavior matters for diagnosis. We check the actual symptom rather than assuming.

The pilot lights but goes out when I release the knob. Why?

That classic symptom usually points to the thermocouple (on a standing-pilot system) — the safety sensor that must heat up and confirm the pilot flame to keep the gas valve open. If it's failing, dirty, or misaligned so it isn't sensing the flame properly, the valve closes and the pilot dies when you let go. It's one of the most common gas fireplace faults, and a well-defined repair once diagnosed.

What's a thermopile, and how is it different from a thermocouple?

Both are flame-sensing safety components, but they do slightly different jobs. A thermocouple generates a small voltage that keeps the pilot valve open. A thermopile (essentially a bundle of thermocouples) generates more voltage — enough to operate the main gas valve and controls, which is why many millivolt gas fireplaces rely on it. A weak or failing thermopile is a frequent cause of a fireplace that won't start or won't stay lit. Testing these tells us which has failed.

Can you just bypass the safety control to make it work?

No — and we want to be emphatic about this. The flame-sensing safety controls exist to shut off gas when there's no flame to burn it, preventing raw gas from flowing into your home. Bypassing or defeating them to force the fireplace to run removes that protection and is genuinely dangerous. We repair or replace the faulty safety component with the correct part so the system works as designed — we never disable a safety control to make a symptom go away, and you shouldn't either.

Why do the replacement parts need to be compatible?

Because ignition components — thermocouples, thermopiles, igniters, modules — are matched to the specific appliance and its valve and control system. The wrong part may not generate the right voltage, fit correctly, or integrate with the safety system, which can leave the fireplace unreliable or unsafe. We use parts compatible with your specific make and model rather than a generic approximation, so the ignition and safety system functions as the manufacturer intended.

Is ignition repair the same as a full gas fireplace repair?

Ignition repair is a focused part of it — specifically the starting and flame-sensing system. A gas fireplace repair is the broader category that also covers shutdowns, burner and flame problems, valves and venting. Most 'won't light' calls are ignition issues, which is why they get their own page, but if the diagnosis points elsewhere we address that instead. We go where the actual fault is.

Should I replace the batteries or try anything myself first?

A few basics are reasonable: on electronic-ignition or remote systems, replacing the batteries is worth trying; confirming the gas is on and following the manufacturer's pilot-lighting instructions is fine. Beyond that — the thermocouple, thermopile, valve, igniter or module — is work with real safety implications, best left to a proper diagnosis. And never attempt anything if you smell gas; leave and call your utility.

Works with

Related services

Chimney and fireplace problems rarely sit in isolation. These related services often come up alongside this one.

A gas log set burning behind glass in a stone-surround fireplace Fireplace

Gas Fireplace Repair

Organize no-start, shutdown, control, burner and venting concerns; explain diagnosis before replacing parts and route active...

View service →
A gas log set burning behind glass in a stone-surround fireplace Cleaning

Gas Fireplace Cleaning & Maintenance

Explain glass/log/burner care, the need for correctly placed components, venting checks, and how maintenance differs from...

View service →
A metal flue cap and storm collar on a factory-built chimney Related

Gas Appliance Chimney & Venting Services

Focus on the chimney/vent serving an appliance, compatibility and observed venting concerns; do not imply general furnace, boiler...

View service →
A modern gas fireplace with a clean-lined surround Fireplace

Fireplace Glass & Door Replacement

Distinguish appliance ceramic glass/sealed assemblies from decorative fireplace doors; confirm model and material suitability...

View service →
A gas log set burning behind glass in a stone-surround fireplace Installations

Gas Log Set Installation

Explain appliance/system compatibility and vented versus other approved configurations; verify actual local/manufacturer...

View service →
A gas fireplace burning behind a glass front Fireplace

Fireplace Blower & Fan Repair

Distinguish room-air circulation blowers from combustion/exhaust fans; assess controls, noise and model-compatible parts without...

View service →

All 76 services →

Serving Missouri, Illinois & Kansas

Ready when you are — available 24/7

Reach the office nearest you, or send your details and we’ll plan the next step.

St. Louis · 314-876-8048 Kansas City · 816-683-1099 Request service

Request Service Call us