A pellet stove is a different animal from a wood stove, and the difference is that it's partly a machine. Where a wood stove simply holds a fire, a pellet stove runs on an orchestra of components — a motor-driven auger feeding fuel, an igniter lighting it, fans managing the air and the heat, sensors watching conditions, and a control board coordinating the whole performance. That sophistication is what gives a pellet stove its steady, thermostat-like convenience, and it's also what gives it more ways to fail. Pellet stove repair is largely about diagnosis: identifying which of those components has stopped doing its job, because the fix is entirely different depending on the answer.
Why it's more complex
It's worth understanding the machine to understand the repair. A pellet stove's main systems are:
- The feed system — the hopper and the auger motor that feeds pellets into the burn pot at a controlled rate.
- The ignition — the igniter element that lights the pellets.
- The fans — a combustion/exhaust fan managing burning and venting, and a convection fan distributing heat.
- The controls and sensors — the board and the sensors that monitor and coordinate everything.
A wood stove has none of this. So a pellet stove can fail in distinctly mechanical and electronic ways — a worn motor, a burned-out igniter, a failing fan, a bad sensor, a control fault — each a separate diagnostic path. The symptom tells us which path to follow.
The "won't start" problem
A no-start is one of the most common calls, and it spans several systems:
- The igniter has failed (it's a wear item that heats every start).
- The auger isn't feeding — jammed, or a failed motor.
- The hopper is empty or jammed.
- A sensor is preventing startup.
- A control or power issue.
The specific behavior narrows it fast: does the stove try to feed pellets? Does the igniter spark or glow? Does it throw an error code? We watch what it actually does rather than guessing, because a no-start from a bad igniter and a no-start from a jammed auger are completely different repairs.
The crucial question: dirty, or broken?
This is the single most important diagnostic distinction in pellet stove repair, so we treat it carefully:
Ash and clinker buildup restricting airflow is a very common cause of shutdowns and faults — and that's resolved by a thorough cleaning, not a repair. But if the stove still shuts down after it's genuinely clean, the cause is likely a failing component — a sensor, a fan, the igniter, or a control issue — and that's a repair.
We don't assume a shutdown is one or the other. Cleaning a stove that has a bad sensor won't fix it; replacing a sensor on a stove that's just clogged is wasteful. So we determine which it actually is. Often a service visit starts with a deep cleaning of the hidden passages and then diagnoses whatever remains — which neatly separates the "it was just dirty" cases from the genuine repairs.
The feed system and the auger
The auger is the heart of a pellet stove's control — a motor-driven screw that feeds pellets into the burn pot at a regulated rate, which is how the stove sets its output. It fails when the motor wears or burns out, when pellets or debris jam it, or when a control problem throws off its timing. The symptoms are a stove that isn't feeding (no fuel reaching the fire) or feeding erratically. A jammed auger sometimes just needs clearing; a failed motor needs replacement with the correct part.
The igniter and the fans
The igniter heats up on every start to light the pellets, so it's a wear item that eventually burns out. A failed igniter is a common, well-defined repair — and while some stoves allow manual lighting as a stopgap, replacing the igniter restores proper automatic operation.
The fans do two different jobs: the combustion/exhaust fan manages burning and pushes exhaust out the vent (a performance and safety matter), while the convection fan distributes heat into the room. Noise, reduced airflow, or shutdowns can point to a fan, and we identify which one and whether it needs cleaning or replacement.
Model-specific parts
Augers, igniters, fans, sensors and control boards are designed for specific makes and models, with the right specifications and fit. Using the correct parts for your unit is essential for proper, safe operation — a generic substitute may not perform correctly or integrate with the controls. Having your make and model lets us source the right components, which is why we ask for it. On a stove that's part machine, the right parts aren't optional.
What affects the scope
Pellet stove repair scope depends on which component has failed, whether the issue is cleaning or a genuine part failure, the make and model and parts availability, and access. Clearing a jam or replacing an igniter is a defined job; an auger motor, a control board, or a multi-component fault is more involved. Diagnosis — including sorting dirty from broken — comes first.
Preparing for the visit
- Describe exactly what happens — won't start, shuts down, won't feed, error codes, noise.
- Try the owner basics first: clean the burn pot and ash pan, check the hopper.
- Have the make and model ready for sourcing parts.
- Let the stove cool and unplug it before we service it.
A pellet stove's complexity is the price of its convenience, and when it acts up, the answer is rarely "just clean it" or "just replace a part" — it's figuring out which. Diagnose the actual failed component, sort the dirty-versus-broken question honestly, and repair it with the right parts, and the steady, set-and-forget warmth you bought the stove for comes right back.